L.W. Zhang
,
J.B. Pei
,
Q.Z. Zhang
,
C.D. Liu
金属学报(英文版)
The inertia friction welding process is a non-linear process because of the interaction between the temperature field and the material properties as well as the friction force. A thermo-mechanical coupled finite element model is established to simulate the temperature field of this process. The transient temperature distribution during the inertia friction welding process of two similar workpieces of GH4169 alloy is calculated. The region of the circular cross-section of the workpiece is divided into a number of four-nodded isoparametric elements. In this model, the temperature dependent thermal properties, time dependent heat inputs, contact condition of welding interface, and deformation of the flash were considered. At the same time, the convection and radiation heat losses at the surface of the workpieces were also considered. A temperature data acquisition system was developed. The temperature at some position near the welding interface was measured using this system. The calculated temperature agrees well with the experimental data. The deformation of the flash and the factor affecting the temperature distribution at the welding interface are also discussed.
关键词:
inertia friction welding
,
null
,
null
黄嘉
,
季英萍
,
秦丽晔
,
吴素君
航空材料学报
doi:10.3969/j.issn.1005-5053.2013.6.008
研究了高温合金GH4169惯性摩擦焊(IFW)焊接接头在室温(23℃)和高温(650℃)下的疲劳裂纹扩展规律.利用金相显微镜(OM)、扫描电镜(SEM)对合金的显微组织和断口形貌进行观察分析.结果表明:在相同温度下,焊缝的裂纹扩展速率低于母材的裂纹扩展速率,这是由于焊缝中的晶界及第二相对裂纹的阻碍效应较强所致.随着温度的升高,母材及焊缝的裂纹扩展速率明显加快,这是由于在高温下晶界弱化,且裂纹尖端加速氧化以及屈服强度和弹性模量降低的共同作用的结果.
关键词:
GH4169高温合金
,
惯性摩擦焊
,
裂纹扩展速率
,
断口形貌
董春林
,
刘川
稀有金属材料与工程
采用轮廓法(contour method)测试小直径FGH96镍基高温合金惯性摩擦焊接接头的内部环向应力.详细介绍了轮廓法测试步骤,包括试样切割、切割面轮廓测试、数据处理和有限元分析;获得了FGH96镍基高温合金惯性摩擦焊接接头内部环向应力分布全貌并分析其分布特征.测试结果表明:镍基高温合金惯性摩擦焊接接头的焊缝中心位置环向应力为非常大的拉应力,峰值拉应力为1200 MPa,达到材料室温时的屈服强度;焊缝区域(距焊缝中心±5 mm区域)近内壁区域的环向应力大于外壁区域环向应力,垂直焊缝方向的环向应力变化梯度非常大;远离焊缝区域,焊缝两侧的环向应力不对称.
关键词:
惯性摩擦焊接
,
镍基高温合金
,
残余应力
,
轮廓法
